Star notes: a small mark from the currency production line
Star notes carry a special suffix in a U.S. banknote's serial number, identifying replacements issued during production. When an imperfect sheet turns up after serial numbers have been printed, a replacement sheet takes its place. Printing the discarded numbers again would be costly and time consuming. Star notes receive their own special serial numbers, ending with a star where a letter would ordinarily appear. The mark records a manufacturing substitution. The Bureau of Engraving and Printing describes this system as a practical response to defects discovered after numbering, when a sheet already has an identity.
The surrounding letters follow rules of their own. Through Series 1995, Federal Reserve notes used one letter, eight digits, and a final letter; $1 and $2 notes retain that arrangement. The opening letter identifies one of the 12 Federal Reserve Banks, running from A through L. The suffix advances after the eight-digit combinations for a bank and series have been used. A series change starts that suffix cycle again at A. The letter O is excluded because it resembles zero, while Z is reserved for test printings. Larger denominations acquired a second prefix letter beginning with Series 1996.
Several other identifiers accompany the serial number. On $5 through $100 notes, a separate letter-and-number designation corresponds to a Federal Reserve Bank, and its letter matches the second serial-number letter. Boston is A1, New York is B2, and San Francisco is L12. A note-position letter and number identifies a location on the printing plate. Face and back plate numbers identify the particular plates used for the two sides. Notes printed at the Fort Worth facility include the small letters FW before the face-plate number. These marks describe different parts of a note's origin.
Sheet layout has changed as well. In 2014, the Bureau began printing $1 notes on sheets containing 50 notes, with positions identified by columns and rows from A1 through J5. The series year has another purpose: it identifies approval of a design or incorporation of a new Treasury secretary's or treasurer's signature. A capital letter following that year signals a significant change in appearance. The Treasury seal to the portrait's right is green, and its English inscription appears on Federal Reserve notes dated Series 1969 or later. None of these identifiers substitutes for the replacement suffix.
Before numbering, currency passes through several printing stages. The paper contains 75 percent cotton and 25 percent linen, with red and blue fibers distributed through it. Background colors on denominations other than $1 and $2 are applied by offset printing. Intaglio printing follows, using ink held in recessed grooves in a plate. Pressure transfers that ink to the paper and leaves a raised image. Portraits, numerals, lettering, and scrollwork are among the features produced this way. On $1 and $2 notes, intaglio is the first printing stage rather than the second.
Inspection helps determine which sheets proceed to numbering. The Offline Currency Inspection System uses cameras and software to examine both sides of untrimmed sheets for quality and quantity. Single Note Inspection can recover acceptable finished notes from defective sheets or production waste. Letterpress supplies the final printed layer, including serial numbers and seals. The Bureau's COPE/PAK equipment combines overprinting with finishing and packaging. Stacks of 100 sheets pass through horizontal and vertical cuts, producing piles of individual notes that receive denomination bands. The inspection, numbering, and finishing operations place the replacement system within a larger manufacturing sequence.
That sequence is changing. In a September 15, 2026, update, Federal Reserve Financial Services described modernization begun in 2023. New equipment produces straps whose serial numbers need not be consecutive. The transition proceeds by denomination, so sequential and nonsequential straps can appear together in currency orders. The update identifies $1, $2, $5, and $20 notes as already being produced on the new equipment. Availability depends on local inventories and distribution schedules. Eventually, the program expects every denomination to use nonsequential production. Some new straps have gaps in their numbers; others have little or no sequencing.
Traditional equipment produces straps of 100 notes that begin with a serial number ending in 01 and finish with one ending in 00. Those endpoint patterns are not expected in nonsequential straps. Traditional equipment continues to use star notes to replace imperfect notes within a strap, but the new equipment will no longer produce them. Existing star notes remain legal tender at face value, regardless of when they were issued. The older replacement mark therefore survives in circulation while the production system that created it gradually gives way to equipment with different numbering and packaging arrangements.
- Bureau of Engraving and Printing, Serial Numbers — www.bep.gov
- U.S. Currency Education Program, Banknote Identifiers and Symbols — www.uscurrency.gov
- Bureau of Engraving and Printing, The Buck Starts Here: How Money is Made — www.bep.gov
- Federal Reserve Financial Services, Nonsequential currency straps, September 15, 2026 — www.frbservices.org